How Do I Change My Bushnell Tour V2 From Meters to Yards?

FAQs Jackson Bowman September 8, 2022

To choose between yards and meters, short press the POWER button to turn on the device (top of the device), look through the eyepiece, press the “MODE” button (left side of the eyepiece) and hold down for about 5 seconds.

How do I change from meters to yards on my Bushnell?

To choose between yards and meters, look through the monocular, press and hold the “Mode” button (left side of the device below the BUSHNELL YARDAGE PRO logo) for about 2 seconds .

How do I change the mode on my Bushnell Tour V2?

The mode button on the left side of the device toggles between Auto Scan and PinSeeker modes (see below for an explanation of these modes) when the button is pressed quickly. or toggle between yards and meters as the default unit of measure by holding down the button for several seconds.

How do you change from meters to yards on the Bushnell Tour V3?

How do I change my Bushnell rangefinder from yards to FEEt?

To choose a different unit of measure, start with the rangefinder off. Hold down the fire button. ‘Y’, ‘M’ or ‘FEEt’ will start flashing as the display slowly cycles through these 3 unit options (5,7b). Release the fire button when the desired display units are flashing.

How do you change from meters to yards on the Bushnell Tour V4?

To choose between yards and meters (starting with the device powered off), press and hold the Power/Fire button. After 7 seconds the display will begin to scroll through the options: yards or meters. When the units you want are displayed, release the Power/Fire button to select them.

How do I reset my Bushnell rangefinder?

The device should switch to USB mode and start charging. – Press and hold the bottom left button and the power button simultaneously for 15 seconds or until the device turns off, then press the power button to turn it back on. This will restart the device and no longer freeze it.

How do I change my rangefinder from meters to yards?

The range finder can be used to measure distances in yards or meters. The units of measure indicators are located in the lower right portion of the LCD. To choose between yards and meters, the device should be turned off. While looking through the eyepiece, press and hold the ON/OFF button for about 5 seconds.

When did the Bushnell Tour V2 come out?

Bushnell introduced the Tour V2 with “Pinseeker Technology” in 2008.

Does the Bushnell Tour V2 have slope?

Bushnell 201933 Overview

The Bushnell Tour V2 Slope Edition is an extremely small and advanced laser rangefinder designed to give golfers quick and accurate readings with the added benefit of some intelligence to help you determine game distances rather than just shot length.

How do I change my Bushnell Hybrid from meters to yards?


Start with the power off to select your preferred units. Hold the Power/FIRE button until you feel the “jerk” vibration (approximately 7 seconds) – the “Y” (Yards) will flash. Continue holding the FIRE button until you see the Units switch to “M” (meters) and then release.

How do you use a Bushnell Tour v3 rangefinder?

How do you change the battery in a Bushnell Tour v2?

Remove the battery cover by lifting the battery cover tab and then twisting it counterclockwise. Insert a CR-2 3 volt lithium battery into the positive end compartment first, then replace the battery cap. NOTE: It is recommended to replace the battery at least every 12 months.

How do you turn off the slope on a Bushnell Tour V4?

On the Tour V4 Slope, clicking and holding the top of the power button will disable the feature to change the settings to be legal for tournament play.

How do you turn on slope tour V4?

How do you change the slope on a Bushnell?

7. Slide the tilt switch to the left (red indicator visible) to enable tilt-compensated distance measurement, slide it to the right (red indicator hidden) to disable tilt. 8. With Tilt mode enabled, tap the mode button to toggle items on/off, indicated by the item mode icon on the display.

How do I update my Bushnell?

You can now quickly and easily update an individual course on your Bushnell device – simply select ‘UPDATE GOLF COURSE’ (at the top of the ‘MY DEVICE’ page), enter the course name in the field Search bar at the top and select the course from the dropdown.



© 2022

We use cookies to ensure that we give you the best experience on our website.
Privacy Policy